Electrical connector commonly used in telephone and computer networks
Left to right, modular connectors: 8P8C plug, 6P6C plug, 6P4C plug, 4P4C plug, 6P6C jack.An 8P8C modular plug. This is the common crimp-type plug, of the same kind pictured above crimped onto a cable (with molded sleeve).
A modular connector is a type of electrical connector for cords and cables of electronic devices and appliances, such as in computer networking, telecommunication equipment, and audio headsets.
Modular connectors were originally developed for use on specific Bell System telephone sets in the 1960s, and similar types found use for simple interconnection of customer-provided telephone subscriber premises equipment to the telephone network. The Federal Communications Commission (FCC) mandated in 1976 an interface registration system, in which they became known as registered jacks. The convenience of prior existence for designers and ease of use led to a proliferation of modular connectors for many other applications. Many applications that originally used bulkier, more expensive connectors have converted to modular connectors. Probably the best-known applications of modular connectors are for telephone and Ethernet.
Accordingly, various electronic interface specifications exist for applications using modular connectors, which prescribe physical characteristics and assign electrical signals to their contacts.
Nomenclature
Modular connectors are often referred to as modular phone jack and plug, RJ connector, and Western jack and plug. The term modular connector arose from its original use in modular wiring components of telephone equipment by the Western Electric Company in the 1960s.[1] This includes the 6P2C used for telephone line connections and 4P4C used for handset connectors.
Registered jack designations describe the signals and wiring used for voice and data communication at customer-facing interfaces of the public switched telephone network. It is common to use a registered jack number to refer to the physical connector itself; for instance, the regular 8P8C modular connector type is often labeled RJ45 because the registered jack standard of the similar name RJ45S specified a similar, but modified, 8P8C modular connector. Similarly, various six-position modular connectors may be called RJ11. Likewise, the 4P4C connector is sometimes called RJ9 or RJ22 though no such official designations exist.[citation needed]
History
The first types of small modular telephone connectors were created by AT&T in the mid-1960s for the plug-in handset and line cords of the Trimline telephone.[1] Driven by demand for multiple sets in residences with various lengths of cords, the Bell System introduced customer-connectable part kits and telephones, sold through PhoneCenter stores in the early 1970s.[2] For this purpose, Illinois Bell started installing modular telephone sets on a limited scale in June 1972. The patents by Edwin C. Hardesty and coworkers, US 3699498 (1972) and US 3860316 (1975), followed by other improvements, were the basis for the modular molded-plastic connectors that became commonplace for telephone cords by the 1980s. In 1976, these connectors were standardized nationally in the United States by the Registration Interface program of the Federal Communications Commission (FCC), which designated a series of Registered Jack (RJ) specifications for interconnection of customer-premises equipment to the public switched telephone network (PSTN).[3][4]
Gender
Modular connectors have gender: plugs are considered to be male, while jacks or sockets are considered to be female. Plugs are used to terminate cables and cords, while jacks are used for fixed locations on surfaces of walls, panels, and equipment. Other than telephone extension cables, cables with a modular plug on one end and a jack on the other are rare. Instead, cables are usually connected using a female-to-female coupler, having two jacks wired back-to-back.
Latching tab and orientation
Most modular connectors are designed with a latching mechanism that secures the physical connection. As a plug is inserted into a jack, a plastic tab on the plug locks against a ridge in the socket so that the plug cannot be removed without disengaging the tab by pressing it against the plug body. The standard orientation for installing a jack in a vertical surface is with the tab down.
The modular plug is often installed with a boot, a plastic covering over the tab and body, to prevent the latching tab from hooking into other cords or edges, which may cause excessive bending or breaking of the tab. Such snagless cords are usually constructed by installing the protective boot before the modular plug is crimped.
Size and contacts
8P8C modular plug contact numbering
Modular connectors are designated using two numbers that represent the maximum number of contact positions and the number of installed contacts, with each number followed by P and C, respectively. For example, 6P2C is a connector having six positions and two installed contacts. Alternate designations omit the letters while separating the position and contact quantities with either an x (6x2) or a slash (6/2).
When not installed, contacts are usually omitted from the outer positions inward, such that the number of contacts is almost always even. The connector body positions with omitted or unconnected contacts are unused for the electrical connection but ensure that the plug fits correctly. For instance, inexpensive telephone cords often have connectors with six positions and four contacts, to which are attached just two wires, carrying only line 1 from a one-, two-, or three-line jack.
The contact positions are numbered sequentially starting from 1. When viewed head-on with the retention mechanism on the bottom, jacks will have contact position number 1 on the left and plugs will have it on the right. Contacts are numbered by the contact position. For example, on a six-position, two-contact plug, where the outermost four positions do not have contacts, the two contacts are numbered 3 and 4.
Modular connectors are manufactured in four sizes, with four, six, eight, and ten positions. The insulating plastic bodies of 4P and 6P connectors have different widths, whereas 8P or 10P connectors share an even larger body width.
Insulation displacement contact types
8P8C plug with contacts for solid wire (left) and stranded wire (right)
Contacts for solid wire (top left) and stranded wire (bottom right)
Internally, the contacts in the plugs have sharp prongs that, when crimped, displace the wire insulation and connect with the conductors inside—a mechanism known as insulation displacement. Cables have either solid or stranded (tinsel wire) conductors, and a given plug is designed for only one type. The sharp prongs are different in the connectors made for each type of wire, and a mismatch between plug type and wire type results in unreliable connections. A modular plug for solid (single-strand) wire often has three slightly splayed prongs on each contact to securely surround and grip the conductor while scraping along the outside, and a plug for stranded wire has prongs that are designed to pierce the insulation and go straight through to contact multiple wire strands.
Interchangeability
Some modular connectors are indexed, meaning their dimensions are intentionally non-standard, preventing connections with connectors of standard dimensions. The means of indexing may be non-standard cross-sectional dimensions or shapes, retention mechanism dimensions or configuration. For example, a Modified Modular Jack using an offset latching tab was developed by Digital Equipment Corporation to prevent accidental interchange of data and telephone cables.
The dimensions of modular connectors are such that a narrower plug can be inserted into a wider jack that has more positions than the plug, leaving the jack's outermost contacts unconnected. The height of the plug's insertion area is 0.260 inches (6.60 mm) and the contacts are 0.040 inches (1.02 mm) apart (contact pitch), so the width is dependent on the number of pin positions.[7][8] However, not all plugs from all manufacturers have this capability, and some jack manufacturers warn that their jacks are not designed to accept smaller plugs without damage. If an inserted plug lacks slots to accommodate the jack's contacts at the outermost extremes, it may permanently deform those outermost contacts of an incompatible jack. Excessive resistance may be encountered when inserting an incompatible plug, as the outermost contacts in the jack are forcibly deformed.
Special modular plugs have been manufactured (for example, the Siemon UP-2468[9]) which have extra slots beyond their standard contacts, to accommodate the wider jack's outermost contacts without damage. These special plug connectors can be visually identified by carefully looking for the extra slots molded into the plug. The molded plastic bodies of the special plugs may also be colored with a light blueish tinge, to aid in quick recognition. The special plugs are preferred for test equipment and adapters, which may be rapidly connected to a large number of corresponding connectors in quick succession for testing purposes. The use of the special plugs avoids inadvertent damage to the equipment under test, even when a narrower plug is inserted into a nominally incompatible wider jack.
Termination
A modular plug crimping tool with exchangeable crimping dies
Termination of cables with modular connectors is similar across the various number of positions and contacts in the plug. The crimping tool contains a die that is often exchangeable and is closely matched to the shape and pin count of the modular plug.
A crimping die-set looks similar to an 8P8C jack, except for the eight teeth lining the top portion of the die. When the tool is operated, the die compresses around the 8P8C plug. As the die compresses, these teeth force the plug contacts into the conductors of the cable being terminated. The crimper may also permanently deform part of the plastic plug body in such a way that it grips the outer sheath of the cable for secure fastening and strain relief. These actions permanently attach the plug to the cable.
Pinout
The contact assignments (pinout) of modular connectors vary by application. Telephone network connections are standardized by registered jack designations, and Ethernet over twisted pair is specified by the ANSI/TIA-568 standard. For other applications, standardization may be lacking; for example, multiple conventions exist for the use of 8P8C connectors in RS-232 applications. For this reason, D-sub-to-modular adapters are typically shipped with the D-sub contacts (pins or sockets) terminated but not inserted into the connector body so that the D-sub-to-modular contact pairing can be assigned as needed.
4P4C
4P4C modular connector on a handset cord.Wired telephone that uses 4P4C connectors for the coiled handset cord.
The four-position four-conductor (4P4C) connector is the standard modular connector used on both ends of telephone handset cords and is therefore often called a handset connector.[10]
This handset connector is not a registered jack, because it was not intended to connect directly to telephone lines. However, it is often referred to as RJ9, RJ10, or RJ22.
Handset wiring
Handsets and often headsets for use with telephones commonly use a 4P4C connector. The two center pins are commonly used for the receiver, and the outer pins connect the transmitter so that a reversal of conductors between the ends of a cord does not affect the signal routing. This may differ for other equipment, including hands-free headsets.
Data port
The Macintosh 128K, Macintosh 512K and Macintosh Plus from Apple as well as the Amiga 1000 from Commodore use 4P4C connectors to connect the keyboard to the main computer housing. The connector provides power to the keyboard on the outer two contacts and receives data signals on the inner pair. The cable between the computer and the keyboard is a coiled cord with an appearance very similar to a telephone handset cable.[11] The connector on the Amiga 1000 uses crossover wiring, similar to a telephone handset. The connector wiring on the Apple computers, however, requires a polarized straight-through pinout. Using a telephone handset cable instead of the supplied cable could short out the +5 volt DC supply and damage the Apple computer or the keyboard.[12]
Modular connectors are often used for data links, such as serial line connections, because of their compact dimensions. For example, some DirecTV set-top boxes include a 4P4C data port with an adapter cord to connect to a computer serial port to control the set-top box.[13]
6P6C
6P4C crimp-on style connector.
Modular plugs are described by the maximum number of physical contact positions and the actual number of contacts installed in these positions. The 6P2C, 6P4C, and 6P6C modular connectors are probably best known for their use as RJ11, RJ14, and RJ25 non-powered registered jacks, respectively (and 6P4C and 6P6C for powered RJ11 and RJ14, power being delivered on the outer pairs). These interfaces use the same six-position modular connector body but have different numbers of pins installed.
RJ11 is a physical interface often used for terminating single telephone lines. RJ14 is similar, but for two lines, and RJ25 is for three lines. RJ61 is a similar registered jack for four lines, but uses an 8P8C connector.
RJ11 wiring
Cables sold as RJ11 often actually use 6P4C connectors (six positions, four contacts) and RJ14 wiring – four wires running to a central junction box. Two of its six possible contact positions connect tip and ring, and the other two contact positions may be unused or provide low-voltage power for night light or other features on the telephone set. In some installations, an extra contact was also required for the ground connection for selective ringers.
Pinout
The pins of the 6P6C connector are numbered 1 to 6, counting left to right when holding the connector tab side down with the opening for the cable facing the viewer.
^Established in the 1950s for polyethylene-insulated conductor (PIC) cable.Horn, F. W. (October 1958). "'Even-Count' Cable"(PDF). Bell Laboratories Record. 37 (5): 208–217. Retrieved October 13, 2022.
^While the old solid color code was well established for pair 1 and usually pair 2, there are several conflicting conventions for pair 3 (and sometimes even pair 2). The colors shown above were taken from a vendor of silver satin flat 8-conductor phone cable that claims to be standard. 6-pair solid (old) bellwire cables previously used by the Bell System use white for pair 3 tip but some vendors' cable may substitute orange for white. At least one other vendor of flat 8-conductor cable uses the sequence blue, orange, black, red, green, yellow, brown and white/slate.[citation needed]
^This color scheme originates in the (withdrawn) national standard DIN 47100. The scheme shown here is the correct color code for interfacing with the RJ connector standards.
However, with German domestic telephone equipment, and that in some neighboring countries, 6P4C plugs and sockets are typically only used to connect the telephone cord to the phone base unit, whereas the mechanically different TAE connector is used at the other end to connect to a service provider interface. Older base units may accommodate the additional connectors of TAE (E, W, a2, b2) and may feature non-RJ standard sockets that can be connected directly to TAE plugs. Further, flat DIN 47100 cables typically place the wires in ascending order. When used directly with 6P4C plugs, the color coding may be undetermined.
Powered version of RJ11
In the powered version of the RJ11 interface, pins 2 and 5 (black and yellow) may carry low-voltage AC or DC power. While the telephone line on pins 3 and 4 (red and green) supplies enough power for most telephone terminals, old telephone terminals with incandescent lights, such as the Western Electric Princess and Trimline telephones, need more power than the phone line can supply. Typically, the power on pins 2 and 5 is supplied by an AC adapter plugged into a nearby power outlet which potentially even supplies power to all of the jacks in the house.
Compatibility with structured cabling
Structured cabling networks adhering to ANSI/TIA-568, ISO/IEC 11801 (or ISO/IEC 15018 for home networks) are widely used for both computer networking and analog telephony. These standards specify the T568A or T568B wiring arrangements compatible with Ethernet. The 8P8C jack used by structured cabling physically accepts the 6-position connector used by RJ11, RJ14 and RJ25. Only RJ11 and RJ14 have full electrical compatibility because Ethernet-compatible pin-outs split the third pair of RJ25 across two separate cable pairs, rendering that pair unusable by an analog phone. Both the third and fourth pairs of RJ61 are similarly split. The incompatible T568A and T568B layouts were necessary to preserve the electrical properties of the third and fourth pairs for Ethernet, which operates at much higher frequencies than analog telephony. Because of these incompatibilities, and because RJ25 and RJ61 were never very common, the T568A and T568B conventions have largely displaced RJ25 and RJ61 for telephones with more than two lines.
8P8C
An 8P8C modular plug not yet crimped onto a cableAn 8P8C female modular connector with a key cut (the connector used in the obsolete RJ45S specification)
The 8 position 8 contact (8P8C) connector is a modular connector commonly used to terminate twisted pair and multi-conductor flat cable. These connectors are commonly used for Ethernet over twisted pair, registered jacks and other telephone applications, RS-232 serial communication using the ANSI/TIA-568 (formerly TIA/EIA-568) and Yost standards, and other applications involving unshielded twisted pair, shielded twisted pair, and multi-conductor flat cable.
An 8P8C modular connection consists of a male plug and a female jack, each with eight equally spaced contacts. On the plug, the contacts are flat metal bars positioned parallel to the connector body. Inside the jack, the contacts are metal spring wires angled away from the insertion interface. When the plug is mated with the jack, the contacts meet and create an electrical connection. The spring force of the jack contacts ensures a good interface.
Left: Generic 8P8C (or 8PMJ, 8-position modular jack) male connector. Right: RJ45 male connector (with key)
Although commonly referred to as RJ45 in the context of Ethernet and category 5 cables, RJ45 originally referred to a specific wiring configuration of an 8P8C connector.[14][15][16] The original telephone-system-standard RJ45 plug has a key that excludes insertion in an un-keyed 8P8C socket.[17]
The original RJ45S[a] was intended for high-speed modems and is obsolete. The RJ45S jack mates with a keyed 8P2C modular plug,[18][19] and has pins 4 and 5 (the middle positions) wired for the ring and tip conductors of a single telephone line and pins 7 and 8 shorting a programming resistor. This is a different mechanical interface and wiring scheme than ANSI/TIA-568 T568A and T568B schemes with the 8P8C connector in Ethernet and telephone applications. Generic 8P8C modular connectors are similar to those used for the RJ45S variant, although the RJ45S plug is keyed and not compatible with non-keyed 8P8C modular jacks.
Telephone installers who wired RJ45S modem jacks or RJ61X telephone jacks were familiar with the pin assignments of the standard. However, the standard un-keyed modular connectors became ubiquitous for computer networking and informally inherited the name RJ45.
Standardization
The shape and dimensions of an 8P8C modular connector are specified for US telephone applications by the Administrative Council for Terminal Attachment (ACTA) in national standard ANSI/TIA-1096-A and international standard ISO-8877. This standard does not use the short term 8P8C and covers more than just 8P8C modular connectors, but the 8P8C modular connector type is the eight-position connector type described therein, with eight contacts installed.
For data communication applications (LAN, structured cabling), International Standard IEC 60603 specifies in parts 7-1, 7-2, 7-4, 7-5, and 7-7 not only the same physical dimensions but also high-frequency performance requirements for shielded and unshielded versions of this connector for carrying frequencies up to 100, 250 and 600 MHz.
Pinout
T568A wiring, defined in TIA-568T568B wiring, defined in TIA-568
8P8C connectors are frequently terminated using the T568A or T568B assignments that are defined in ANSI/TIA-568. The drawings to the right show that the copper connections and pairing are the same, the only difference is that the orange and green pairs (colors) are swapped. A cable wired as T568A at one end and wired as T568B at the other end (Tx and Rx pairs reversed) is an Ethernet crossover cable. Before the widespread acceptance of auto MDI-X capabilities, a crossover cable was needed to interconnect similar network equipment (such as Ethernet hubs to Ethernet hubs). Crossover cables are sometimes still used to connect two computers together without a switch or hub, however, most network interface cards (NIC) in use today implement auto MDI-X to automatically configure themselves based on the type of cable plugged into them. A cable wired the same at both ends is called a patch or straight-through cable, because no pin/pair assignments are swapped. If a patch or straight cable is used to connect two computers with auto MDI-X capable NICs, one NIC will configure itself to swap the functions of its Tx and Rx wire pairs.
Pin numbering on plug face. Connected pins on plug and jack have the same number.
2
3
green solid
2
orange solid
TD−
DA−
ring
3
2
white/orange stripe
3
white/green stripe
RD+
DB+
tip
4
1
blue solid
1
blue solid
not used
DC+
ring
5
1
white/blue stripe
1
white/blue stripe
not used
DC−
tip
6
2
orange solid
3
green solid
RD−
DB−
ring
7
4
white/brown stripe
4
white/brown stripe
not used
DD+
tip
8
4
brown solid
4
brown solid
not used
DD−
ring
Types and compatibility
Two types of 8P8C plugs and crimping tools for installing the plug onto a cable are commonly available: Western Electric/Stewart Stamping (WE/SS) and Tyco/AMP. While the two types are similar, the tooling and plug types cannot be interchanged.[b] WE/SS compatible plugs are available from a large number of manufacturers, whereas Tyco/AMP plugs are produced exclusively by Tyco Electronics.[citation needed] Both types of modular plugs can be mated with a standard 8P8C modular jack.
Both types of 8P8C plugs are available in shielded and unshielded varieties for different attenuation tolerances as needed. Shielded plugs are more expensive and require shielded cable, but have a lower attenuation, and may reduce electromagnetic interference.
Although a narrower 4-pin and 6-pin plug fits into the wider 8-pin jack and makes a connection with the available contacts on the plug, because the body of the smaller connector may stress the remaining contacts,[c] the smaller connector can potentially damage the springs of the larger jack.
Applications
8P8C connectors are commonly used in computer networking applications, where interconnecting cables are terminated at each end with an 8P8C modular plug wired according to TIA/EIA standards. Most wired Ethernet communications are carried over Category 5e or Category 6 cable terminated with 8P8C modular plugs. The connector is also used in other telecommunications connections, including ISDN and T1.
Where building network and telephone wiring is pre-installed, the center (blue) pair is often used to carry telephony signals. While this allows an RJ11 plug to connect, it may damage the modular jack; an approved converter prevents damage. In landline telephony, an 8P8C jack is used at the point a line enters the building to allow the line to be broken to insert automatic dialing equipment, including intrusion alarm panels.
8P8C modular connectors are also commonly used as a microphone connectors for PMR, LMR, and amateur radio transceivers. Frequently the pinout is different, usually mirrored (i.e. what would be pins 1 to 8 in the ANSI/TIA-568 standard might be pins 8 to 1 in the radio and its manual).
In analog mobile telephony, the 8P8C connector was used to connect an AMPS cellular handset to its (separate) base unit; this usage is now obsolete.
The physical connector is standardized as the IEC 60603-7 8P8C modular connector with different categories of performance. The physical dimensions of the male and female connectors are specified in ANSI/TIA-1096-A and ISO-8877 standards and normally wired to the T568A and T568B pinouts specified in the ANSI/TIA-568 standard to be compatible with both telephone and Ethernet.
A similar standard jack once used for modem and data connections, the RJ45S, used a keyed variety of the 8P8C body with an extra tab that prevents it from mating with other connectors; the visual difference compared to the more common 8P8C is subtle, but it is a different connector. The original RJ45S[18][24] keyed 8P2C modular connector, obsolete today, had pins 5 and 4 wired for tip and ring of a single telephone line and pins 7 and 8 shorting a programming resistor.
Electronics catalogs commonly advertise 8P8C modular connectors as RJ45. An installer can wire the jack to any pin-out or use it as part of a generic structured cabling system such as ISO/IEC 15018 or ISO/IEC 11801 using 8P8C patch panels for both phone and data.
Crossover cables
A router-to-router crossover cable uses two 8-position connectors and a unshielded twisted pair (UTP) cable with differently wired connectors at each end.
10P10C
The pin arrangement for a 10P10C socketA 10P10C plug
The 10P10C connector is commonly referred to as an RJ50 connector,[citation needed] although this was never a standard registered jack. The 10P10C has 10 contact positions and 10 contacts.
The most common uses of the 10P10C connector are in proprietary data transfer systems.[25]
ANSI/TIA-1096-A: Telecommunications telephone terminal equipment connector requirements for connection of terminal equipment to the telephone network
IEC 60603-7-1: Connectors for electronic equipment: Part 7-1: Detail specification for 8-way, shielded free and fixed connectors with common mating features, with assessed quality
IEC 60603-7-2: Connectors for electronic equipment: Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz
IEC 60603-7-4: Connectors for electronic equipment: Part 7-4: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz
IEC 60603-7-5: Connectors for electronic equipment: Part 7-5: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz
IEC 60603-7-7: Connectors for electronic equipment: Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 600 MHz
ISO/IEC 8877, EN 28877: Information Technology—Telecommunications and Information Exchange between Systems—Interface Connector and Contact Assignments for ISDN Basic Access Interface Located at Reference Points S and T
^The often omitted S suffix indicates this is a wiring configuration supporting a single telephone line.
^WE/SS and Tyco/AMP 8P8C plugs have different spacings for the cable strain relief.[21][22] Using a WE/SS 8P8C crimp die set on a Tyco/AMP 8P8C plug crushes the top of the connector and damages the crimp die set, and vice versa.
^The body of a 6P6C or 4P4C plug typically projects out by more than one millimeter further than the contacts and presses the outermost contacts of the larger connector further than if a full-size connector were inserted.
^4P4C and 10P10C connectors are not defined in these standards.
References
^ abKrumreich C.L., Mosing L.W., The Evolution of a Telephone, Bell Laboratories Record 44(1) p.14 (January 1966)
^Walden S.W., Telephone Sets Go Mod (Modular, That Is), Bell Laboratories Record, Vol. 52(8) p. 238 (Sept. 1974)
^AT&T, Registration Interface—Selection and General Information, Bell System Practices, Section 463-400-100 Issue 1, May 1976
^"Mac Plus Keyboard Cable", Syrinx, UK: Megadon, ...the cable is the same as the telephone cable that connects handsets to the phone, unfortunately [...] this type of cable and pretty much any type of pre manufactured cable [...] is wired wrong for the Mac Plus. Under no circumstances should you use this cable as you will damage your keyboard and/or your Mac!
^Trulove 2005, pp. 23, 132: Designing LAN Wiring Systems: The 8-pin modular jack is sometimes referred to as an "RJ-45", because the connector/jack components are the same. However, RJ-45 actually applies to a special purpose jack configuration that is not used in LAN or standard telephone wiring. […] Work Area Outlets: Modular jacks are often referred to as "RJ-45" jacks. This is not really the correct moniker, although it is in very common use.
^Oliviero, Andrew; Woodward, Bill (July 20, 2009). "Connectors". Cabling: The Complete Guide to Copper and Fiber-Optic Networking (4th ed.). Sybex. p. 294. ISBN978-0-470-47707-6. The RJ (registered jack) prefix is one of the most widely (and incorrectly) used prefixes in the computer industry; nearly everyone, including people working for cabling companies, is guilty of referring to an eight-position modular jack (sometimes called an 8P8C) as an RJ-45.
^Semenov, Andrey B.; Strizhakov, Stanislav K.; Suncheley, Igor R. (October 3, 2002). "Electrical Cable Connectors". Structured cable systems. Springer. p. 129. ISBN3-540-43000-8. The traditional 8-contact connector, which is called Western Plug, 8PMJ (8-position modular jack), 8P8C (8 position 8 conductor), or somewhat incorrectly RJ-45, is used widely in SCS practice.
^Trulove 2005, p. 219: User Cords and Connectors: This 8-pin modular plug is probably the most subject to name abuse, because it resembles the specialized RJ-45 connector. However, the RJ-45 wiring pattern (which includes an interface programming resistor) is so radically different from that of T568A and B that it really should not be called by that name at all.
Artikel ini membutuhkan rujukan tambahan agar kualitasnya dapat dipastikan. Mohon bantu kami mengembangkan artikel ini dengan cara menambahkan rujukan ke sumber tepercaya. Pernyataan tak bersumber bisa saja dipertentangkan dan dihapus.Cari sumber: Jambul sagittal – berita · surat kabar · buku · cendekiawan · JSTOR (November 2019) Jambul sagittal Paranthropus aethiopicus di atas kepalanya Jambul sagittal adalah sebuah tonjolan tulang yang membujur di sepan…
Albert KesselringKesselring menggunakan seragam Salib Kesatria dari Salib Besi pada tahun 1940JulukanPaman AlbertLahirPendapat pertama Kesselring lahir pada (1885-11-20)20 November 1885 Pendapat kedua Kesselring lahir pada (1881-08-08)8 Agustus 1881Pendapat pertama Kesselring lahir di Marktsteft, Kerajaan Bavaria, Kekaisaran Jerman Pendapat kedua Kesselring lahir di Bayreuth, JermanMeninggal16 Juli 1960(1960-07-16) (umur 74)Bad Nauheim, Hessen, Jerman BaratPengabdian Kekaisaran Jerman …
Bönningstedt. Bönningstedt adalah kota yang terletak di distrik Pinneberg, Schleswig-Holstein, Jerman. Kota Bönningstedt memiliki luas sebesar 12.05 km². Bönningstedt pada tahun 2006, memiliki penduduk sebanyak 4.141 jiwa. lbsKota dan kotamadya di Pinneberg (distrik) Appen Barmstedt Bevern Bilsen Bokel Bokholt-Hanredder Bönningstedt Borstel-Hohenraden Brande-Hörnerkirchen Bullenkuhlen Ellerbek Ellerhoop Elmshorn Groß Nordende Groß Offenseth-Aspern Halstenbek Haselau Haseldorf Haslo…
Candi Panataranꦕꦢꦶꦥꦤꦠꦫꦤ꧀Kompleks Candi Penataran: Candi Candra Sengkala, dengan Candi Naga dan Candi Utama di belakangnya.Location within IndonesiaInformasi umumGaya arsitekturCandiKotaPenataran, Nglegok, Blitar, Jawa Timur.Negara IndonesiaMulai dibangun1194 Masehi (pada masa pemerintahan Kertajaya)[1]RampungTerus ditambah dan digunakan hingga 1415 Masehi. Di era modern dilakukan pemagaran dan penambahan bangunan pendukungData teknisSistem strukturCandi dan teras b…
Disambiguazione – Se stai cercando altri significati, vedi Libano (disambigua). Libano (dettagli) (dettagli) (AR) كلنـا للوطـن للعـلى للعـلمKullunā li-l-waṭan li-l-ʿulā li-l-ʿalam(IT) Tutti noi per la patria, la gloria e la bandiera Libano - Localizzazione Dati amministrativiNome completoRepubblica Libanese Nome ufficiale(AR) الجمهورية اللبنانيةal-Jumhūriyya al-Lubnāniyya Lingue ufficialiarabo Altre linguefrancese Capitale Beirut (1 2…
Sudut kota Racine Racine merupakan sebuah kota di Amerika Serikat. Kota ini letaknya di bagian utara. Tepatnya di negara bagian Wisconsin. Pada tahun 2010, kota ini memiliki jumlah penduduk sebesar 78.860 jiwa dan memiliki luas wilayah 48,4 km². Kota ini memiliki angka kepadatan penduduk sebesar 2.033,8 jiwa/km². Pranala luar Situs resmi Diarsipkan 2010-09-19 di Wayback Machine. Racine.WI.Net Diarsipkan 2007-11-15 di Wayback Machine. Racine County Convention and Visitors Bureau Racine His…
العلاقات المجرية الموزمبيقية المجر موزمبيق المجر موزمبيق تعديل مصدري - تعديل العلاقات المجرية الموزمبيقية هي العلاقات الثنائية التي تجمع بين المجر وموزمبيق.[1][2][3][4][5] مقارنة بين البلدين هذه مقارنة عامة ومرجعية للدولتين: وجه المقارنة ا…
Peta menunjukan lokasi Pasacao Pasacao adalah munisipalitas yang terletak di provinsi Camarines Sur, Filipina. Pada tahun 2015, munisipalitas ini memiliki populasi sebesar 49.035 jiwa. Pembagian wilayah Secara politis Pasacao terbagi menjadi 19 barangay, yaitu: Antipolo Bagong Silang Bahay Balogo Caranan Cuco Dalupaon Macad (Hebrio Lourdes) Hubo Itulan Odicon Quitang Salvacion San Antonio San Cirilo (Pob.) Santa Rosa Del Norte (Pob.) Santa Rosa Del Sur (Pob.) Tilnac Tinalmud Galeri Pemandangan P…
الأكاديمية العسكرية المصريةكلية الدفاع الجوي شعار كلية الدفاع الجوي (مصر)الشعار الشعار إيمان . عزم . مجد معلومات التأسيس 1974 (منذ 50 سنة) تتبع جامعة الأكاديمية العسكرية المصرية النوع كلية عسكرية الموقع الجغرافي إحداثيات 31°16′19″N 30°06′16″E / 31.271967°N 30.104449°E / 31.271967; 30.104…
Lynne Ann Vincent Cheney Istri Wakil PresidenAmerika SerikatMasa jabatan20 Januari 2001 – 20 Januari 2009 PendahuluTipper GorePenggantiJill BidenChair of the National Endowment for the Humanities ke-6Masa jabatan1986–1993 PendahuluWilliam J. BennettJohn Agresto (acting)PenggantiSheldon HackneyJerry L. Martin and Donald Gibson (acting) Informasi pribadiLahir14 Agustus 1941 (umur 82)Casper, WyomingSuami/istriDick CheneyHubunganWayne Vincent dan Edna LybyerAnakElizabeth, MaryAlma …
Islam menurut negara Afrika Aljazair Angola Benin Botswana Burkina Faso Burundi Kamerun Tanjung Verde Republik Afrika Tengah Chad Komoro Republik Demokratik Kongo Republik Kongo Djibouti Mesir Guinea Khatulistiwa Eritrea Eswatini Etiopia Gabon Gambia Ghana Guinea Guinea-Bissau Pantai Gading Kenya Lesotho Liberia Libya Madagaskar Malawi Mali Mauritania Mauritius Maroko Mozambik Namibia Niger Nigeria Rwanda Sao Tome dan Principe Senegal Seychelles Sierra Leone Somalia Somaliland Afrika Selatan Sud…
Arata IsozakiArata Isozaki pada 2013Lahir(1931-07-23)23 Juli 1931[1]Ōita, JepangMeninggal29 Desember 2022(2022-12-29) (umur 91)Tokyo, JepangKebangsaanJepangAlmamaterUniversitas Tokyo (1954)PekerjaanArsitekPenghargaanPenghargaan Pritzker 2019[2]GedungFestival Plaza at EXPO70Art Tower MitorLA’s Museum of Contemporary Art Arata Isozaki pada 1996 Arata Isozaki (磯崎 新, Isozaki Arata; 23 Juli 1931 – 29 Desember 2022) adalah seorang arsitek, perancang kota, …
فيرزن علم شعار الإحداثيات 51°15′20″N 6°23′30″E / 51.25557°N 6.39168°E / 51.25557; 6.39168 [1] تقسيم إداري البلد ألمانيا ألمانيا الغربية (23 مايو 1949–2 أكتوبر 1990)[2][3] خصائص جغرافية المساحة 91.1 كيلومتر مربع (31 ديسمبر 2017)[4] ارتفاع 40 متر عدد ال…
Stream in Georgia and North Carolina, United States Brasstown CreekTributary to Hiwassee RiverBrasstown Creek as it runs through Brasstown, N.C. in 2023Location of Brasstown Creek mouthLocationCountryUnited StatesStateNorth CarolinaGeorgiaCountiesClay (NC)Union (GA)Towns (GA)Physical characteristicsSourcedivide between Brasstown Creek and Nottely River • locationabout 2 miles north of Brasstown Bald • coordinates34°52′35″N 083°48′50″W / …
Suhardi Komandan Komando Operasi Khusus (Dankoopssus) TNI ke-4PetahanaMulai menjabat 17 November 2023 PendahuluJoko Purwo PutrantoPenggantiPetahana Informasi pribadiLahir25 Oktober 1968 (umur 55)Jepara, Jawa TengahAlma materAkademi Militer (1990)Karier militerPihak IndonesiaDinas/cabang TNI Angkatan DaratMasa dinas1990—sekarangPangkat Mayor Jenderal TNINRP1900010811068SatuanInfanteri (Kopassus)Sunting kotak info • L • B Mayor Jenderal TNI Suhardi, S.I.P. (l…
Muhammad Ali Jinnah محمد علی جناحમુહમ્મદ અલી જિન્નાહ Gubernur Jenderal PakistanMasa jabatan14 Agustus 1947 – 11 September 1948Penguasa monarkiGeorge VIPerdana MenteriLiaquat Ali KhanPendahuluThe Earl Mountbatten of Burma (sebagai Wakil Raja India)PenggantiKhawaja NazimuddinKetua Majelis NasionalMasa jabatan11 Agustus 1947 – 11 September 1948WakilMaulvi Tamizuddin KhanPendahuluJabatan baruPenggantiMaulvi Tamizuddin KhanKetua Majel…
A food stand sells chuối nếp nướng in southern Vietnam. Chuối nếp nướng, also known as grilled banana wrapped in sticky rice, is a popular street food in Vietnam, particularly in the southern region. History Chuối nếp nướng is thought to have originated from southern province of Bến Tre, Vietnam; it quickly became the province's specialty and then spread to the south and all over Vietnam.[1][2][3] Over time, the dish has evolved, with each vendor in…
Dewan Perwakilan Rakyat DaerahKota SamarindaDewan Perwakilan RakyatKota Samarinda2019-2024JenisJenisUnikameral Jangka waktu5 tahunSejarahSesi baru dimulai26 Agustus 2019PimpinanKetuaSugiyono (PDI-P) sejak 9 November 2020 Wakil Ketua IHelmi Abdullah (Gerindra) sejak 29 Juli 2020 Wakil Ketua IIRusdi (Golkar) sejak 9 Oktober 2019 Wakil Ketua IIISubandi (PKS) sejak 9 Oktober 2019 KomposisiAnggota45Partai & kursi PKB (3) Gerindra (8) PDI-P (8) …
1799 poem And backwards and forwards he switch'd his long tail, As a gentleman switches his cane.—Illustration from the 1830 edition of The Devil's Walk, attributed to Professor Porson The Devil's Thoughts is a satirical poem in common metre by Samuel Taylor Coleridge, published in 1799, and expanded by Robert Southey in 1827 and retitled The Devil's Walk. The narrative describes the Devil going walking and enjoying the sight of the various sins of mankind. The poem was …
DC comic book universe character For the professional wrestler, see Jimmy Olsen (wrestler). Comics character Jimmy OlsenArt by Phil Noto from 9-11: The World's Finest Comic Book Writers and Artists Tell Stories to RememberPublication informationPublisherDC ComicsFirst appearanceAnonymous cameo:Action Comics #6 (November 1938)As Jimmy Olsen:Radio: The Adventures of Superman radio serial (April 15, 1940)Comics: Superman #13 (November–December 1941)Created byJerry SiegelJoe ShusterBob MaxwellIn-s…